Skip to content

Transforming Objects

(Available in All DoubleCad Variants)

Default UI Menu: Modify/Transform

Ribbon UI Menu:

imgThe Transform tools enable you to quickly move, rotate, or scale objects. You can optionally leave the original object in place, creating a copy. In addition, you can record the transform operations for use on other objects. You can display the Transform toolbar by right-clicking in any toolbar area and selecting Transform. img The Transform tools can be used on 2D and 3D objects. For the objects you want to use, be sure the Selector is set correctly (2D, 3D, or both).

Note: The Assemble tool also enable you to move and rotate objects, relative to other objects or locations. Assemble tools require more accurate input than Transform tools, however, and do not create copies. See

The Transform tools are typically invoked when objects are already selected. You can also invoke them even if no objects are currently selected, as long as the Select tool is active. In this case, the local menu option Select can be used to select objects to copy. Close the Select option when all objects are selected. For each of the transform tool (Move, Rotate, Scale, and Generic), the following local menu options are available: Select: Enables you to add or remove objects from the selection set. When the correct objects have been selected, deactivate this object to continue with the operation.

img

Repeat: Enables you to transform or copy the selected objects again. Otherwise, the function ends once the first operation is complete.

img

Keep Original Object: Activated by default, makes a copy of the selected objects. Otherwise the object is simply transformed.

img

Finish: Complete the transform operation.

img

Generic

img

Default UI Menu: Modify/Generic

Ribbon UI Menu:

imgTransforms a 3D object by selecting six points. The first two points define the movement distance, similar to using Move. The third and fourth points enable you to rotate the object in the current workplane. The fifth and sixth points enable you to flip the object.

Note: The Generic Transform tool is also available from the local menu of the selector tool.

Local menu options: Scaling: Enables you to change the object's scale while transforming.

img Keep Aspect Ratio: If Scaling is used, choose whether to maintain the object's aspect ratio.

img Skew: If Scaling is used and Keep Aspect Ratio is not used, you can scale the object while transforming.

img

Move

img

Default UI Menu: Modify/Move

Ribbon UI Menu:

imgMoves or copies objects relative to two defined points.

  1. Select the objects you want to move or copy, and activate Move.

img5

  1. Select the source point - the first of two points that defines the transform vector.

img

  1. Select the destination point. The objects are moved along the transform vector from their original location.

img

Note: By default, the original objects remain in place. If you do not want to create a copy, deselect the local menu option Keep Original Object.

  1. The new or moved object is now the one selected. Click outside to deselect it.

img

If you use the local menu option Repeat, you can transform the selected objects again. Otherwise the operation ends.

img

Rotate

img

Default UI Menu: Modify/Rotate

Ribbon UI Menu:

imgRotates and/or copies objects relative to three defined points.

  1. Select the objects you want to rotate or copy, and activate Rotate.

img

  1. From the local menu or Inspector Bar, select the axis of rotation (X, Y, or Z).

img

  1. Select the center of rotation.

img

  1. Select the source and destination points - these establish the transform angle relative to the rotation center.

img

  1. The objects are moved along the transform angle from their original location.

img

Note: By default, the original objects remain in place. If you do not want to create a copy, deselect the local menu option Keep Original Object.

  1. The new or moved object is now the one selected. Click outside to deselect it.

img

If you use the local menu option Repeat, you can transform the selected objects again. Otherwise the operation ends.

img

Scale

img

Default UI Menu: Modify/Scale

Ribbon UI Menu:

imgScales and/or copies objects relative to three defined points.

  1. Select the objects you want to scale or copy, and activate Scale.

img

  1. Select the scaling start point and end point.

img

When selecting the destination point, the closer to the scaling end point, the closer the scale approaches 1:1.

img

The closer to the scaling start point, the scale approaches zero.

img

  1. Select the scaling destination point.

img

  1. The objects are scaled, relative to their original location.

img

Note: By default, the original objects remain in place. If you do not want to create a copy, deselect the local menu optionKeep Original Object.----

  1. The new or moved object is now the one selected. Click outside to deselect it.

img

If you use the local menu option Repeat, you can transform the selected objects again. Otherwise the operation ends.

Additional local menu option: Keep Aspect Ratio: By default, the objects are scaled so that all dimensions remain proportional to the original. img Deactivate this option if you want to be able to change the aspect ratio.

img

Transform Recorder

(Available in XT Pro)

Default UI Menu: Modify/Transform Recorder

Ribbon UI Menu:

imgEnables you to record a transformation and apply it to other objects.

  1. Select the objects whose transformation you want to record.

img

  1. Click Start Transform Recorder.

img

  1. Perform the transformation, using the Move, Rotate, Scale, and Generic tools as needed. In this example, Move with Keep Original Object was used to copy the object from Point 1 to Point 2. Then Rotate was used on the copied object, with Keep Original Object turned off.

img

  1. When the transformation is complete, click Stop Transform Recorder.

img

  1. Add a new object or group of objects to which to apply the recorded transformation.

img

  1. Select this object and click Apply Stored Transformation.

img

  1. The Move and Rotate commands are applied to the selected object.

img

  1. If you want to apply the transformation with different settings, click Player.

img

  1. In the Inspector Bar you can specify the number of sets (the number of additional copies) to create. Set any additional parameters in the local menu or Inspector Bar, and click Play.

imgI

In this example, the transformation was applied to the previous copy, and three additional copies were made.

img

It is important to note that Play (Apply Stored Transformation) uses settings from the Player (Customize and Apply Stored Transformation). Player options remain in effect until changed, and will affect subsequent transformations, even if they are re-recorded.

Note: If you specify multiple Sets and Keep Original Objects is turned off, the selected objects will be transformed by the distance times the number of sets. No copies will be made.

Local menu options: Only one option is unique to Player. Toggle CS - If not selected, the object will be rotated around the center of the original object. If selected, the reference point of the new object will be used as the center of rotation.